Moses Ludel Vlog: Why Build a Jeep 4.6L Stroker Inline Six?

Moses Ludel Vlog: Why Build a 4.6L Jeep Inline Six Stroker Motor? The Jeep inline six stroker motor is a popular topic! In this HD vlog, Moses Ludel shares his many reasons for building a 4.6L Jeep inline six stroker motor. At left is the predecessor to the seven-main bearing 199/232/258 and 4.0L AMC engine […]

How-to Build a Multipurpose Jeep 4.6L Stroker Motor

Q&A Vlog: How-to Build a Multipurpose Jeep 4.6L Stroker Motor In this HD video vlog Q&A, Moses Ludel discusses the Jeep 4.0L inline six build-up into a stroker 4.6L engine. The build consists of the right design, correct choice of parts and the required machining. Moses Ludel describes the engine parts and machining options and […]

Moses Ludel’s 4WD Mechanix Magazine – Jeep Fuel Pressure Requirements

Moses Ludel’s 4WD Mechanix Magazine – Jeep Fuel Pressure Requirements

Jeep How-to: Fuel Pressure Needs for Carburetion and Fuel Injection      Carburetion and TBI run at a much lower fuel pressures than MPI systems. BBD carburetors require only 4-5 PSI fuel pump pressure! The 2.5L TBI normally runs 14-15 PSI. 1991-95 MPI systems operate at 31-39 PSI. Normal pressure for a TJ system is from 49.2 +/- […]

Moses Ludel’s 4WD Mechanix Magazine – How-to: Oil Filtration for 4.0L and Stroker Inline Six Build-ups

Moses Ludel’s 4WD Mechanix Magazine – How-to: Oil Filtration for 4.0L and Stroker Inline Six Build-ups

Oil Filtration for Jeep 4.2L, 4.0L and Inline Six Stroker Motors The 4.0L swap into an earlier Jeep CJ or YJ Wrangler 2.5L four or 4.2L inline six chassis has become popular. So is the stroker build-up that uses the 4.0L inline six engine block.      Jeep 4.0L and stroker inline six buildups have become popular. 4.0L conversions […]

Moses Ludel’s 4WD Mechanix Magazine – How-to: Tuning the Carbureted Jeep Inline Six Stroker Motor

Moses Ludel’s 4WD Mechanix Magazine – How-to: Tuning the Carbureted Jeep Inline Six Stroker Motor

How-to: Tuning the Jeep Carbureted Inline Six Stroker Motor! Important: Many 1972-90 Jeep inline six models still require periodic emission control inspection. To avoid failing an emission inspection, make sure that the carburetor and ignition system comply with local, state and federal requirements…. 1) The common stroker build uses a 4.0L block and 4.0L cylinder head (for fit […]

Moses Ludel’s 4WD Mechanix Magazine – Vlog: Road Testing Jeep 4.6L Stroker Inline Six

HD Vlog: Performance Testing a 4.6L Jeep Inline Six Stroker Motor! Hosted by Moses Ludel  The Jeep inline six stroker motor has been a popular topic! In this HD vlog, hear Moses Ludel describe a Hewes Performance Machine engine that now powers a 1998 Jeep XJ Cherokee. Hear Moses’ comments on this engine build and how the […]

Moses Ludel’s 4WD Mechanix Magazine – HD Videos: Jeep CJ-8 4.6L Stroker Power

Two HD Videos: Hewes Performance 4.6L Stroker Powers a Jeep CJ-8 Scrambler In addition to the two HD videos on this page, see the complete HD video series on building a Jeep 4.6L inline six stroker motor. There are six Tony Hewes interviews listed at the ‘4WD Tech How-to Channel’ playlist! Mark’s freshly installed engine […]