Click Here for Access to the Mobile Version of This Website!           Click here for direct access to the 4WD Mechanix Magazine Facebook Page!  Join Us at Facebook![

Click the 4WD Mechanix Video Network button for access to the HD video channel playlists. For a complete list of articles and videos, click the "Site Content Directory" button!

Enter your keywords here and click!

 

How-to: Grand Cherokee 231 Transfer Case, Part 2: Assembly with an SYE

Comparison of output shafts: stock and SYE.

26: Stock Jeep 231 output shaft (left) is still in good condition. This NV231 transfer case is undergoing a conversion to a shorter output shaft (right) with a fixed yoke output flange. The Advance Adapters kit for the Jeep NP231 or NV231 is thorough, consisting of a new output shaft, shorter housing and all hardware needed.

   Note: Not only is the Advance Adapters output shaft (right) shorter, it is also very stout in diameter and stronger at the yoke output end. This is where the 50% increase in stamina occurs. Note the precise match of these two shafts. Machine work and materials found in this kit are of exceptional quality, providing maximum service and proper fit.

New output shaft assembly begins with sprocket.

27: Assembly lube protects parts during initial start up and eases assembly. Here, mode hub and drive sprocket mount on the new output shaft, with a new snap ring installed. Always make sure snap rings seat completely, all the way around. Do not over-stretch a snap ring during installation. Expand a snap ring just enough to clear the shaft.

Shift range fork and rail in position with shift hub sleeve.

28: There is no need to remove the planetary system unless you are completely rebuilding the unit. Here, the range fork and hub are in position, showing the relationship of parts. Make sure the fork engages the shift sector slot and stays in that position during assembly! Installing the mode fork and its rail (see #29) will help keep the range fork in alignment.

Assembled shift mechanism and output shaft components.

29: This is the correct relationship of parts on a clean, assembled new mainshaft. Note the direction of the mode hub sleeve. Make sure all nylon fork slippers are intact and engaged with the mode shift sleeve. The mode fork must seat in the hub sleeve groove.

    Note: The mode fork rail runs through the centered range fork. Keep these parts carefully aligned during assembly. Lube friction surfaces with assembly lube.

New output shaft and assembled parts installed in case.

30: The output shaft in place, note the relationship of these parts. Lube moving pieces and align them without force. Keep the output shaft and the shift rail on center, aligned with bearings, splines and case bores.

    Note: The NP/NV231 is is not a complex mechanism; however, every part must align properly. Use caution and do not force parts. You will find Advance Adapters’ instructions very helpful.

Installing chain and sprockets in the NP/NV231.

31: The chain and front output shaft with sprocket go into the case together. Aligning the output shafts and carefully fitting the chain make the outer case installation possible. Fit the front output shaft into its bearing. Do not force these parts together. When you install the U-joint yoke, it will seat the shaft against the bearing's collar. 

Checking chain slack with shafts aligned.

32: Aligning the outer end of the output shaft will remove chain slack. Note: Without the rear case half installed, there is slack in the chain. This is normal. If you suspect chain wear, compare the chain's length with a new one.

33: Center up the shift rail. Make sure that the fork engages the shift sleeve properly. These parts must remain in position as the rear case half goes into place. The mode fork spring (shown) goes outboard of the mode fork. Be sure to install this spring and keep it in place during assembly of the rear case. 

Oil filter and pickup tube for NP/NV231.

34: Make certain that the oil filter and tube align correctly. This tube must be in place or the pump will not pick up oil. Use care and make sure the tube, pump inlet O-ring, hose and filter align in their factory positions before the case halves go together.

Caution: The filter and tube should be clear and free of any debris, or the pump will become damaged. The O-ring must seal properly. The magnet must be clean and back in the case. Make sure the mode fork spring is in place, too.

Use proper sealant on the case halves.

35: Use Jeep recommended Mopar RTV or a high-quality equivalent. I run a uniform, 1/8” wide bead of sealant around the rear case half. Circle the bolt holes, and stay in the center of the machined surface. Since the halves are precisely machined, the mating faces will squeeze sealant over the surface. Excess sealant is unnecessary. However, make sure there are no sealant gaps that could leak.

Placing case halves together and installing oil pump.

36: The pump and case halves go in place together. Keep the pump in position to assure proper oil tube engagement. Center the cases to prevent smearing sealant as you bring the case halves into alignment. Use the dowels as a guide, and keep case faces parallel. The mode fork rail must fit properly through the rear case bore. All parts should align as you bring the halves together evenly and snugly. I use Loctite 242 (blue) on bolt threads and finger-tighten the two dowel bolts to keep the case halves aligned.

Case halves aligned and bolts going into place.

37: Bring all bolts up evenly. I use a speed handle for this chore. Tighten in cross, a few threads at a time to keep the case halves parallel and prevent binding of any internal parts. Watch the oil pump to be sure it stays engaged in the oil tube. With all bolts snug, final tightening is with a torque wrench. Recheck torque after parts set for a few minutes.

New speedometer sleeve on SYE Kit installation.

38: Install the Advance Adapters speedometer drive (speed sensor) sleeve with its snap rings. The stock output shaft has speedometer drive teeth cut into the shaft. The nylon sleeve approach works nicely, providing a serviceable part. The sleeve has inner splines for indexing.

Aligning the mode fork in the rear case half.

39: Case halves securely tightened together, the shift rail gets checked for stickout height. The new retainer/output shaft housing will go into place next.

Prepping new output retainer housing for installation.

40: An even bead of RTV sealant will assure a leak-proof new retainer/tailhousing. I have greased the new seal lip and will use Loctite 242 on bolts threads. Carefully align the oil pump tangs with the new tailhousing’s flanges. (You may need to rotate the pump slightly, but be certain not to dislodge the pump from the oil pickup tube.) Align the retainer with the bolt holes, keeping all parts square. Tighten bolts evenly and in cross.

Note: Final torque specifications are in the Advance Adapters instructions. At the end of this section, I have included the Jeep factory torque recommendations for the NV231.

Install retainer bolts and torque them to spec.

41: Final tightening is in cross and with a torque wrench. Bring retainer flushly to the case. Tighten gradually to prevent binding. After parts set for several minutes, I check torque once more, in cross and sequence. 

Installing yoke flanges with sealant.

42: New retainer housing in place, I install the 32-spline output yoke supplied by Advance Adapters. Brush a thin, even film of Super 300 or similar sealant on the inner spline threads. Also coat the machined inner seat of the yoke (as shown). These added steps prevent oil from seeping between the shaft splines and yoke. Note the new rubber seal that fits between the shaft threads and yoke nut. 

New flange yoke nut and thread locker.

43: New yoke is now in place. Sealant on splines and a new rubber yoke seal (provided by Advance Adapters) assure leak-free service. Loctite 271 (red) is additional insurance, used with a new, self-locking pinion flange nut. On hard steel assemblies and threads, Loctite 271 acts as a thread locker and added sealer.

Tightening output yoke flange nut.

44: Although I have the Jeep-recommended flange holding tool, this is an alternative that works. I protect the yoke flange with a rag and hold the outer yoke while tightening with a large torque wrench. Initial tightening is with an air gun, set to below the final torque recommended. 

Use of professional flange yoke holding wrench.

45: This is the Jeep-recommended tool for holding the U-joint flange. Final torque is with a large torque wrench. Make certain that yoke flanges have been properly sealed and torqued to specification. Once done properly, these yokes will not need further attention. Each output yoke will now accept a CV-type driveline assembly. The new Advance Adapters rear yoke flange accepts the popular 1310 size Spicer CV joint.

Installing speed sensor and speedometer driven gear.

46: I clean the outside of the speedometer housing with a rag and alcohol. Coat the O-ring lightly with RTV sealant as recommended in the Advance Adapters instructions. This unit fits the new tailhousing/retainer perfectly. The original alignment marks will also work here, as the clamp bolt locates just like the original, 1999 XJ housing.

    Caution: Make sure that the speedo clamp indexes for the correct tooth count and engagement of the speedometer gears.

Mode rail bore end plug installed.

47: Here, I install the mode rail bore’s end plug and gasket supplied. Secure this plug to assure a leak-free seal. A thin film of RTV sealant helps.

Filling the NV231 on the bench.

48: Before installing the transfer case assembly, I fill the unit to specified capacity with Mopar’s Dexron-III/Mercon ATF. At that point, I seal the vent tube temporarily with a vacuum cap and rotate the transfer case assembly slowly in all directions. This checks for leaks and also coats all parts with ATF. Remove vacuum cap before installing vent hose.

 Note: 2.5 pints of lube/ATF is the approximate fill. I put 2 pints in the unit on the bench and top it off once installed in the chassis. 

Unit now ready for installation in the chassis.

49: NV231 transfer case now boasts an Advance Adapters 'SYE' kit upgrade! The unit will perform better than new. The NP/NV231 is not complicated, and if rebuilt properly, it can be a very reliable unit. There are aftermarket, lower range gear sets available for these units. The stock ratio is 2.72:1 in low range, 1:1 in high range.

NV231 back in the chassis!

50: The NV231 transfer case is now back in the chassis! The unit is ready for a CV-type rear driveline, just part of the 6-inch, long-arm suspension lift upgrade to this 1999 XJ Cherokee. This 231 transfer case, with a 4.0L inline six, 4.10:1 gears, ARB Air Lockers front and rear, and 33" diameter tires, will handle some rough terrain!

NV231 Torque Chart

Jeep "factory" torque/tightening specifications for the NV231 transfer case. (Specs are similar for the NP231.) For the output yoke nut and other 'SYE' related tightening specifications, refer to the guidelines furnished with the Advance Adapters 'SYE' Fixed Yoke Kit. I advise using a Mopar service manual to perform this work. Access the Mopar TechAuthority II Website for factory manuals and technical information:

www.techauthority.com

BFG Tires—official sponsors at 4WD Mechanix Magazine and HD Video Network!

Click for direct access to the Bestop® official website! 

Click on the logo for direct access to the Dynamic Diesel, Inc., official website! 

Click here for direct access to the Advance Adapters website! 

Warn Industries, click on logo for access to the official site! 

4WD Mechanix Magazine is a proud charter member of the Nevada Four-Wheel Drive Association!

UFWDA Logo 240 px 

4WD Mechanix Magazine is a SEMA Member!

Click here for access to the Bentley Publishers website and Jeep Owner's Bible, 3rd Edition, by Moses Ludel. 

Jeep® Owner's Bible by Moses Ludel—available for more than two decades and a best seller!

 Click here for access to the Bentley Publishers website and information about the 1946-71 CJ Jeep Rebuilder's Manual by Moses Ludel.

Each of Moses Ludel's Jeep® books earned an official Mopar® part number!

 Click here for access to the Bentley Publishers website and information about the 1972-86 CJ Jeep Rebuilder's Manual by Moses Ludel.

For 4x4 Jeep®, Truck and SUV technical information, make this magazine your professional resource!

 Ford F-Series Pickup Owner's Bible by Moses Ludel (Bentley Publishers)

Moses Ludel's Ford F-truck and GM truck books earned official Ford Motor Company 'SVO' and GM Motorsport part numbers!

 Chevrolet & GMC Light Truck Owner's Bible by Moses Ludel (Bentley Publishers)

 Toyota Truck & Land Cruiser Owner's Bible by Moses Ludel (Bentley Publishers)

The Toyota Truck and Land Cruiser book by Moses Ludel is a classic among vintage Toyota pickup and FJ40 Land Cruiser owners!

Find Moses Ludel's books at:  Bentley Publishers, Amazon.com, Barnes & Noble, Advance Adapters, 4WD Hardware, Quadratec, Willys Jeep® Parts, 4x4Books—plus independent book stores and 4WD outlets!

Click here for direct access to the 4WD Mechanix Magazine Facebook Page!