How-to: Jeep 231 Transfer Case Rebuild with Slip Yoke
Eliminating the slip yoke rear driveline and upgrading to Advance
Adapters’ Fixed-Yoke (SYE) kit increases the rear output stamina of this NP/NV231 transfer case. The unit will now
handle a six-inch chassis lift and 33” diameter tires. A "Slip Yoke Eliminator Kit" allows use of a longer,
constant velocity (CV) driveline.
See the following
two pages for Part 1 and Part 2 of the NP/NV231 step-by-step
The NP- and NV231 transfer case is the most widely used design in the
world. These units were popularized in the XJ Cherokee, YJ/TJ Wrangler, Grand Cherokee and various truck models
built by Jeep and a variety of other manufacturers. This is a rugged and reliable, chain-drive transfer case that
can handle off-pavement chores and reasonable (33"-35") diameter tires. Like any other automotive mechanism, the NP
and NVG231 transfer case will require rebuilding at higher mileage or if abused.
Owners of Jeep YJ and TJ Wranglers, Jeep XJ Cherokees and Jeep Grand
Cherokees quite often perform a chassis lift. The increased driveline angles make vibration more likely and
decrease the strength of the U-joints. By design, a common cross-type, single Cardan style U-joint loses strength
as the driveline angle or slope increases.
The popular solution is a heavy-duty, constant velocity (CV) rear
driveline. Jeep NP/NV231 transfer cases typically operate with a CV front driveline. However, most 231 units use a
splined output shaft with a slip yoke driveshaft. For the modified or lifted Jeep Wrangler, Grand Cherokee or XJ
Cherokee, the relatively short, stock driveshaft and slip yoke design create problems when the driveline angle
steepens. The more chassis lift, the more trouble!
Advance Adapters is a manufacturer of transmission adapters and engine
retrofit kits for a variety of popular 4x4 vehicles. Recognizing the demand for a CV rear driveline on Jeep
Wrangler and Cherokee models equipped with New Process or New Venture 231 type transfer cases, Advance Adapters
created its “Slip Yoke Eliminator” (SYE) kit. The kit eliminates the splined output shaft and slip yoke style rear
driveline. In place of the sliding yoke, the SYE kit provides a new, heavy-duty output/mainshaft and a fixed-yoke
flange. The new flange will accept a custom-built driveline with a heavy-duty Spicer CV
This well-engineered kit provides several gains. The new 32-spline
output shaft and fixed yoke provide a 50% increase in output stamina over the stock output shaft and slip yoke.
This enables the NP/NV231 transfer case to handle more horsepower, larger tires and steeper driveline angles. For
lifts, the shortened output assembly allows the use of a much-needed, longer rear
Advance Adapters makes this fixed-yoke kit available for popular Spicer
1310 or 1350 CV type flanges. There is even an option for 1310 or 1350 non-CV yokes, satisfying users who want a
single (Cardan) cross-type joint with a longer rear driveline. A longer driveline will reduce U-joint angles and
decrease stress to the driveshaft and joints.
An additional gain with the SYE kit is the fixed rear output shaft yoke
and seal design. To prevent oil leakage on a stock NP/NV231 with a splined output and slip yoke, the rear driveline
must remain in place. Removal of the slip-yoke driveshaft opens the transfer case to a huge fluid
The Advance Adapters’ SYE fixed-yoke approach seals the output and
permits driving the vehicle with the rear driveline removed (using four-wheel drive mode to propel the front axle).
In a backcountry emergency, a damaged rear driveline will not leave your vehicle stranded. You can remove the rear
driveshaft and drive the vehicle in “front-wheel drive mode,” much like a Jeep CJ or TJ Wrangler Rubicon model! You
cannot do this with a slip yoke driveline...
An Advance Adapters ‘SYE’ fixed-yoke kit fits all Jeep Wrangler and XJ
Cherokee models equipped with either the New Process or New Venture 231 transfer case. The kit serves as a direct
bolt-in for the TJ Wrangler and later XJ Cherokee applications of the 231. For Wrangler YJ models and earlier XJ
Cherokees equipped with the NP231, slight modifications enable installation of this same kit. The well-detailed
instructions that come with the Advance Adapters kit explain which areas might require attention or minor
By installing the Fixed-Yoke ‘SYE’ conversion, the 231 transfer case has
increased stamina and versatility. Reducing the excessive length of the stock 231 transfer case allows use of a
chassis lift, oversized tires and a CV driveshaft to decrease rear driveline stress. If your Jeep Wrangler, Grand
Cherokee or XJ Cherokee has an NP or NV 231 transfer case, the Advance Adapters’ Fixed Yoke conversion is a
valuable asset for any degree of chassis lift.
The transfer case rebuild that I have illustrated in this 'how-to' is a
1999 XJ Cherokee NV231 application. The installation of an SYE from Advance Adapters is straightforward, actually a
bolt-on setup that requires no additional modifications to the transfer case. With a six-inch lift kit and 33”
diameter tires on the agenda, the SYE kit and a constant velocity (CV) rear driveshaft is a
Consider a CV-type rear driveline as part of your chassis lift plans.
For builders who have a YJ or TJ Wrangler, a Grand Cherokee or an XJ Cherokee with the NP231 or NV231, review this
complete rebuild and SYE installation. Advance Adapters' Slip Yoke Eliminator or ‘SYE’ conversion is a much needed
part of any suspension lift!
information about Advance Adapters is available at 1-800-350-2223 or the website: www.advanceadapters.com.
For details on the rear CV driveline component, see the suspension lift
article within this XJ Cherokee Workshop section of the website. A six-inch long arm suspension lift, 33" diameter
tires and an SYE rebuild of the NV231 transfer case have been trail tested—substantially—for several years now.
Simply put, the '99 XJ Cherokee holds its own on hardcore trails...Moses Ludel
Part 1 of this 'how-to' is the disassembly and inspection of an NP/NV231
transfer case. Part 2 is the assembly and installation of an SYE kit. The work necessary to perform an SYE kit
makes rebuilding the transfer case practical.